192.168.30.1 is a private IPv4 address inside 192.168.0.0/16, the block RFC 1918 sets aside for private networks along with 10.0.0.0/8 and 172.16.0.0/12. With a netmask of 255.255.0.0 the block holds 65,536 addresses. It is the consumer block: nearly every home router, mobile hotspot and small office access point ships a default gateway inside it, which is why it is the range most people encounter. Because the space is reserved rather than assigned, no registry records an owner for this address and no ISP, organisation or country can be attached to it. The same address is in use simultaneously on countless unrelated networks worldwide, and routers on the public internet drop traffic addressed to it, so it is only reachable from inside the local network it belongs to.
Within its /24 subnet, 192.168.30.0/24, the usable host addresses run from 192.168.30.1 to 192.168.30.254, with 192.168.30.255 reserved as the broadcast address. This address sits at position 1, the first usable slot, which is the conventional place for a router or gateway. That convention is a habit rather than a rule, and 32 other addresses in the same subnet are separately documented as things people look up.
Of the vendors known to ship equipment with this address as a default, Ubiquiti appears on EdgeRouter and UniFi hardware. A third-party network administrator can also assign 192.168.30.1 to any gateway, so it turns up on segmented networks where a guest, IoT or lab VLAN was given its own /24. Most people arriving here are trying to open the device's administration interface to change a Wi-Fi password, forward a port, or check why the connection is down.
To open the admin panel, type 192.168.30.1 into your browser's address bar. If the page does not load, this is probably not the gateway address on your network — see the checks below. http://192.168.30.1
5 default username and password pairs have been reported for devices answering on 192.168.30.1, ordered by how often each one is seen.
| Username / Password | Percentage |
|---|---|
| admin / admin | 36% |
| root / NetC0mmV3oo | 36% |
| super / sp-admin | 9% |
| admin / Motorola | 9% |
| root / NetC0mmV2oo | 9% |
Reported default credentials for devices at this address are spread across several pairs rather than concentrated in one. Two pairs account for roughly 36 percent of reports each: admin/admin and root/NetC0mmV3oo. Three more each account for around 9 percent: super/sp-admin, admin/Motorola, and root/NetC0mmV2oo. On Ubiquiti EdgeRouter and UniFi hardware the documented default is ubnt/ubnt.
Those figures describe what has been reported for this address, not what is on any particular unit. Check the label on the underside or back of the device first, since many routers now ship with a unique per-unit password printed there. If the device came from an ISP, the credentials may be in the supplied documentation or set to an account number. Any password changed during setup overrides all of the above.
| Vendor | Models | Username / Password |
|---|---|---|
| Ubiquiti | EdgeRouter, UniFi | ubnt / ubnt |
If no credential combination works, a factory reset restores the documented defaults. On Ubiquiti EdgeRouter and UniFi hardware this is done with the physical reset button: with the device powered on, hold the button, commonly for around ten seconds, until the status lights change, then release and wait for the device to finish rebooting. Some models require a paperclip because the button is recessed.
A reset is not free. It erases the Wi-Fi network name and password, so every connected device must be rejoined, and it discards port forwarding rules, static DHCP reservations, VLAN configuration, firewall rules and any DNS settings. On a network segmented into a 192.168.30.0/24 subnet, that segmentation is itself part of the configuration and may be lost. Export a configuration backup first if the interface is still reachable, and note any ISP-supplied connection settings before starting.
Reset method by vendor:
Type 192.168.30.1 into your browser's address bar and press Enter. Type it by hand rather than accepting an autocomplete suggestion, which often fills in a different address you visited before.
If the browser reports that it cannot reach 192.168.30.1, this is not the gateway address on your network. On Windows run ipconfig /all and read the Default Gateway line; on macOS open System Settings, Network, Details, TCP/IP; on Linux run ip route and read the address after "default via".
If the login page loads but rejects your credentials, and you have never changed them, use the defaults printed on the device's label. If they have been changed and nobody knows the new password, a factory reset is the only way back in.
Confirm you are connected to the network the device serves, by cable or Wi-Fi, not to a neighbouring network or a VPN. A VPN or proxy will send the request out to the internet, where private addresses are discarded. Disable both and retry. Then try http://192.168.30.1 explicitly, since typing the bare address may push it into a search engine.
On Windows run ipconfig /all in Command Prompt and read the Default Gateway line for your active adapter. On Linux run ip route and look at the address after "default via". On macOS open System Settings, Network, then Details for the active connection and check the TCP/IP tab. If the gateway shown is not 192.168.30.1, use the address it reports instead.
Your computer can only reach 192.168.30.1 directly if it holds an address in 192.168.30.0/24, meaning 192.168.30.1 through 192.168.30.254. If ipconfig or ip route shows an address such as 192.168.1.50, you are on another segment and the request will be routed away. Reconnect to the correct network, or release and renew the DHCP lease.
Many devices serve their admin page over plain HTTP on port 80; others redirect to HTTPS and present a self-signed certificate, which browsers flag as untrusted. That warning is expected on a local device and can be accepted here. If neither works, some interfaces listen on an alternate port such as 8080 or 8443, entered as http://192.168.30.1:8080.
Reaching the login form proves the device is up and the address is right. Check the label for a per-unit password before trying the reported defaults, and watch for caps lock, since pairs like root/NetC0mmV3oo and super/sp-admin are case sensitive. Some devices lock out after several failed attempts, so wait a few minutes rather than retrying rapidly.
Write it as 192.168.30.1 with three dots and no leading zeros. Common slips are 192.168.30.l with a lowercase L, 192.168.3.1 with a digit dropped, 192.168.301 with a dot missing, and 192.168.30.1.1. Also avoid www or a .com suffix; this is a numeric address on your own network, not a public hostname.
192.168.30.1 is often mistyped. These all refer to the same address:
l92.l68.30.l, 192.168.3o.1, 192.168..30.1, 192 168 30 1, 192.168.30.1..
The most common slip is typing a lower-case letter L in place of the digit 1, or the letter O in place of a zero.
The 192.168.30.0/24 subnet runs from 192.168.30.1 to 192.168.30.254, with 192.168.30.255 reserved as the broadcast address. These are the addresses in it we hold router login details for.
33 addresses in this subnet have a page; the most looked-up are listed here.
~$ curl https://www.proxydocker.com/api/v2/free/8.8.8.8
{
"ipAddress": "8.8.8.8",
"countryCode": "US",
"countryName": "United States",
"stateProv": "California",
"city": "Mountain View"
}The free API is limited to 500 daily requests and returns city-level location data only. For larger volumes or more data such as latitude/longitude, ISP details and proxy detection, see our commercial offers.
Copyright © 2026 Proxydocker.com, all rights reserved. · Privacy policy · Affiliate program