10.0.30.1 is a private IPv4 address drawn from 10.0.0.0/8, the largest of the three ranges RFC 1918 sets aside for private use. That block carries a 255.0.0.0 netmask and 16,777,216 addresses, and none of them are routed across the public internet. Because the space is reusable by anyone, the address has no geographic location, no ISP, no owner and no registrant. Any organisation may number a device 10.0.30.1 inside its own network, and a great many do; the same address on a different network is a different machine entirely. You can only reach it from inside the network that defines it, over Ethernet, Wi-Fi or a VPN tunnel into that network.
Within that block the address sits in 10.0.30.0/24, a 254-host subnet whose usable range runs from 10.0.30.1 to 10.0.30.254, with 10.0.30.255 reserved as the broadcast address. 10.0.30.1 is the first usable address, the position most administrators reserve for the default gateway, which is why it commonly answers as a router, firewall or layer-3 switch interface rather than as an ordinary host. A /24 carved this far down out of a /8 is a deliberate design decision, and the third octet usually encodes something specific: a VLAN, a floor, a branch office, a lab segment. A further 106 addresses in the same /24 are documented separately, which is what you would expect of a range in day-to-day use.
No specific vendor is known to ship 10.0.30.1 as a factory default gateway. Addresses in 10.0.0.0/8 are far more often assigned by whoever designed the network: corporate and campus deployments, ISP-managed customer equipment, carrier-grade gear, VPN address pools and container or orchestration networks. Roughly two thousand lookups a year arrive for this address, most from people trying to open an admin interface, work out what device is answering, or confirm that 10.0.30.1 is their gateway at all.
To open the admin panel, type 10.0.30.1 into your browser's address bar. If the page does not load, this is probably not the gateway address on your network — see the checks below. http://10.0.30.1
We hold no reported default credentials for 10.0.30.1. That is not a gap to fill with a guess: no vendor is documented as shipping this address as a factory default, so any list published for it would be invented. The credentials you need belong to whichever device holds this address on your own network.
Where to find them:
There are no documented default username and password pairs for 10.0.30.1. That is not an oversight: since no vendor is known to ship this address from the factory, there is no factory credential set attached to it, and any pair published for it elsewhere would be guesswork. Do not trust lists that offer one.
Find the device's own defaults instead. Check the label on the underside or rear panel, the quick-start card in the box, or the manual for the exact model and hardware revision. If the equipment was supplied by an ISP, the credentials are usually printed on the unit or held in your account portal. On a corporate or campus network numbered from 10.0.0.0/8, the login was almost certainly set by an administrator and no default applies; ask whoever runs the network.
Because no vendor is identified for 10.0.30.1, no single reset procedure can be given. The common pattern on consumer and small-business equipment is a recessed reset button held for roughly ten to thirty seconds while the device is powered on, but the exact hold time and behaviour vary, so confirm it against the documentation for your specific model before pressing anything.
A reset is not cheap. It clears the Wi-Fi name and passphrase, port forwards, static DHCP leases, VLANs, firewall rules and any PPPoE or ISP credentials. On a network deliberately numbered in 10.0.0.0/8, expect the address itself to change: factory defaults usually fall in another range, so the device may come back on a 192.168 address rather than 10.0.30.1. On ISP-managed or centrally managed corporate gear a reset can drop the service entirely and require a support call to reprovision.
Type 10.0.30.1 into your browser's address bar and press Enter. Type it by hand rather than accepting an autocomplete suggestion, which often fills in a different address you visited before.
If the browser reports that it cannot reach 10.0.30.1, this is not the gateway address on your network. On Windows run ipconfig /all and read the Default Gateway line; on macOS open System Settings, Network, Details, TCP/IP; on Linux run ip route and read the address after "default via".
If the login page loads but rejects your credentials, and you have never changed them, use the defaults printed on the device's label. If they have been changed and nobody knows the new password, a factory reset is the only way back in.
On Windows run ipconfig /all in Command Prompt and read the Default Gateway line for your active adapter. On Linux run ip route and look at the address after "default via". On macOS open System Settings, Network, select the active connection, then Details and the TCP/IP tab. If the gateway shown is not 10.0.30.1, that is the address to open instead.
You must be attached to the network that uses 10.0.30.1, physically or through a VPN; from any other network the address is unreachable by design. Ping it first to see whether anything answers. If the browser turns your input into a web search, type http://10.0.30.1 in full. Guest or client-isolation Wi-Fi modes also block access to the gateway's management interface.
Management interfaces on 10.0.0.0/8 equipment are frequently HTTPS-only with a self-signed certificate, which produces a browser warning you have to accept explicitly for a private address. Some devices listen on 8080, 8443 or another port instead of 80 and 443. Try http://10.0.30.1, then https://10.0.30.1, then https://10.0.30.1:8443 before concluding the interface is down.
10.0.30.1 is easily confused with 10.0.3.1, 10.30.0.1 and 10.0.30.10, all of which are valid but different hosts. Do not pad the octets: 10.0.030.1 is interpreted as octal by some network stacks and resolves elsewhere. Leave off any www prefix or domain suffix, and keep the dots as separators rather than commas or hyphens.
With no documented defaults for this address, a rejected login usually means the credentials were changed or set by an administrator when the network was built. Check the device label and the model's manual, and confirm Caps Lock is off. Many devices lock out after several failed attempts, so pause for a few minutes rather than retrying, and avoid a reset until you have exhausted the documentation.
The first address in a /24 is a convention, not a rule. On a network subnetted out of 10.0.0.0/8 the host at 10.0.30.1 may be a firewall, a layer-3 switch, a hypervisor interface, a VPN concentrator or a server. If the page you get does not look like a router, compare the address against the default gateway shown by ipconfig /all or ip route.
The 10.0.30.0/24 subnet runs from 10.0.30.1 to 10.0.30.254, with 10.0.30.255 reserved as the broadcast address. These are the addresses in it we hold router login details for.
107 addresses in this subnet have a page; the most looked-up are listed here.
~$ curl https://www.proxydocker.com/api/v2/free/8.8.8.8
{
"ipAddress": "8.8.8.8",
"countryCode": "US",
"countryName": "United States",
"stateProv": "California",
"city": "Mountain View"
}The free API is limited to 500 daily requests and returns city-level location data only. For larger volumes or more data such as latitude/longitude, ISP details and proxy detection, see our commercial offers.
Copyright © 2026 Proxydocker.com, all rights reserved. · Privacy policy · Affiliate program