10.5.0.1 is a private IPv4 address drawn from 10.0.0.0/8, the largest of the three ranges set aside by RFC 1918 for private use. With a netmask of 255.0.0.0, the block spans 16,777,216 addresses, and nothing inside it is routable across the public internet. That size is the reason it turns up where it does: corporate and campus networks, ISP-managed customer premises equipment, carrier-grade gear, VPN address pools and container or orchestration networks all carve it into much smaller pieces, far below a /8. Because the space is unallocated and reusable, no organisation, ISP, country or registrant owns 10.5.0.1. Any claim that this address belongs to a particular company or place is simply wrong; thousands of unrelated networks use it at the same moment.
Within that block, 10.5.0.1 falls in the 10.5.0.0/24 subnet, whose usable host range is 10.5.0.1 to 10.5.0.254, with 10.5.0.255 reserved as the broadcast address. It sits at position one, the first usable address in the subnet. That first-address slot is a conventional place for a gateway, firewall or router interface, since many administrators and default configurations assign the lowest usable address to the device that routes traffic out of the segment. Eleven other addresses in this same /24 are documented alongside it, which is typical of a segment where a handful of infrastructure hosts sit near the bottom of the range.
No specific router vendor, brand or model is known to ship 10.5.0.1 as a factory default gateway. Where it appears, it has almost always been configured deliberately by whoever built the network. Most people looking this address up are trying to reach a login page on it, having seen it as their default gateway, in a VPN client, or in documentation for an office or campus network.
To open the admin panel, type 10.5.0.1 into your browser's address bar. If the page does not load, this is probably not the gateway address on your network — see the checks below. http://10.5.0.1
We hold no reported default credentials for 10.5.0.1. That is not a gap to fill with a guess: no vendor is documented as shipping this address as a factory default, so any list published for it would be invented. The credentials you need belong to whichever device holds this address on your own network.
Where to find them:
There are no documented default username and password pairs for 10.5.0.1, and none should be assumed. Since no vendor ships this address as a factory default, any credentials protecting a device here come from that device's own defaults or, more often, from whoever configured the network. Guessing common pairs is a poor use of time and can trigger lockouts or logged failed-login alerts on managed equipment.
Look instead at the device itself. Many routers and firewalls print default access details on a sticker on the underside or rear panel, alongside the serial number and Wi-Fi key. Failing that, check the model's manual or the ISP's documentation. On a work or campus network, the credentials are held by the administrator, and asking is the correct route.
If no one can supply working credentials, the standard recovery route on most routers and firewalls is a factory reset: hold the recessed reset button, usually pressed with a paperclip, for roughly ten to thirty seconds while the device is powered on, then wait for it to reboot. Some equipment instead requires a console cable and a password-recovery sequence entered during boot.
A reset is not free. It erases the entire configuration, and on a device using 10.5.0.1 that configuration is custom by definition, since this is not a factory default address. Expect to lose the addressing plan, VLANs, firewall rules, port forwards, VPN settings and Wi-Fi credentials, and expect the device to return on a different address entirely. On managed or ISP-supplied hardware, a reset may also break the service until it is reprovisioned.
Type 10.5.0.1 into your browser's address bar and press Enter. Type it by hand rather than accepting an autocomplete suggestion, which often fills in a different address you visited before.
If the browser reports that it cannot reach 10.5.0.1, this is not the gateway address on your network. On Windows run ipconfig /all and read the Default Gateway line; on macOS open System Settings, Network, Details, TCP/IP; on Linux run ip route and read the address after "default via".
If the login page loads but rejects your credentials, and you have never changed them, use the defaults printed on the device's label. If they have been changed and nobody knows the new password, a factory reset is the only way back in.
The address only responds if it exists on the network you are attached to. On Windows, run ipconfig /all and read the Default Gateway line. On Linux, run ip route and look at the default via entry. On macOS, open System Settings, then Network, select the active interface and check Details, TCP/IP. If a different address appears, that is the one to open.
Your own address must fall within 10.5.0.0/24, meaning 10.5.0.1 through 10.5.0.254, for the gateway to be directly reachable. If your machine has an address from a different block, such as 192.168.x.x or 172.16.x.x, or an APIPA address starting 169.254, you are not on this segment and no browser will reach it. Reconnect to the correct network or VPN first.
Addresses in 10.0.0.0/8 are frequently handed out by VPN concentrators and used for remote-access pools. If you reached 10.5.0.1 through a VPN, the address becomes unreachable the moment the tunnel drops or reconnects with split tunnelling that excludes this route. Verify the client shows a connected state, then re-check ip route or ipconfig /all for a route covering 10.5.0.0/24.
Browsers now default to HTTPS, which fails if the device only serves plain HTTP, and vice versa. Type the scheme explicitly: http://10.5.0.1 and then https://10.5.0.1. Administratively configured equipment is often moved off the standard ports, so also try appending a port, for example https://10.5.0.1:8443 or http://10.5.0.1:8080. Accept the certificate warning; self-signed certificates are normal here.
Type the address into the URL bar, not a search box, or the browser will run a web search instead of connecting. Common slips include writing 10.5.o.1 with a letter o, adding www, or transposing digits to 10.50.1 or 10.5.1.0. There is no domain name involved, so the address must be entered exactly, with three dots and four numbers.
Because 10.5.0.1 is not a factory default address, the login on it has usually been changed from whatever the device shipped with. Repeated attempts can lock the account or raise alerts on monitored equipment. Check the label on the hardware, then the manual, then the person or team who set the network up. Caps lock and autofilled entries from a different device are frequent culprits.
The 10.5.0.0/24 subnet runs from 10.5.0.1 to 10.5.0.254, with 10.5.0.255 reserved as the broadcast address. These are the addresses in it we hold router login details for.
12 addresses in this subnet have a page; the most looked-up are listed here.
~$ curl https://www.proxydocker.com/api/v2/free/8.8.8.8
{
"ipAddress": "8.8.8.8",
"countryCode": "US",
"countryName": "United States",
"stateProv": "California",
"city": "Mountain View"
}The free API is limited to 500 daily requests and returns city-level location data only. For larger volumes or more data such as latitude/longitude, ISP details and proxy detection, see our commercial offers.
Copyright © 2026 Proxydocker.com, all rights reserved. · Privacy policy · Affiliate program